Wednesday, February 17, 2021

How to Build a Toy Box

Today's project is a toy box. Last summer, my then 6 year old really wanted a toy box. One day we went out and made one. It's a pretty quick project. You can make it in an afternoon.

DIY Toy Box


DIY TOY BOX

wooden toy chest



It all started with this Berenstain Bears book. We got it from the library. My daughter was intrigued by the toy box that Papa built to help the cubs keep their room clean. She just had to have her own. I happened to have some 1X10's in the garage from another project. So a few weeks later I built my two little girls their own little toy boxes.

picture of a book

Note: This diy was originally posted 4-30-15. My 6 year old is now 13! Time sure does fly. 

Supplies Needed for a Toy Chest                

You will need:
  • 1 - 8 ft  1X10
  • 1 - 8 ft  1X4
  • 1 - 8 ft  1X2
  • power saw
  • brad nail gun - I used 18 gauge brad nails that were 1 1/4" long
  • wood glue
  • 2 - 2" hinges
  • wood putty for filling holes
  • screw driver
  • paint or stain, if desired

Cut List for a Toy Chest


I like to cut the pieces as I go, measuring the box for an exact measurement to get the best fit. This is especially important for the last piece on the cut list.
Cut List:

  • 2 - 22" pieces of 1 X 10
  • 2 - 10" pieces of 1 X 10
  • 3 - 25" pieces of 1 X 4
  • 3 - 6" pieces of 1 X 2
  • 1 - 22" piece of 1 X 10 - *wait to cut this piece until you have assembled most of the box and measured the spot where this piece goes*


 Be sure to sand the pieces well before assembling. It is much harder to sand in the corners of the finished box than a flat piece of wood.

Assembling the Toy Box


two boards making the beginnings of a toy box
Begin with your two 22" pieces of 1X10. Place one on top of the other at the edge. Apply wood glue liberally and then nail the piece in place from the bottom. This is best achieved with two people in order to keep it square.

A note about wood glue: Use a liberal amount. The glue is what is holding the boards together. The nails are just to hold it in place until the glue has dried. Make sure to use a damp paper towel and wipe up any glue that squeezes out while it is still wet. Glue is super hard to sand off after it's dried.

putting boards together to make a toy box
 Using your 10" piece of 1X10 attach it to the end, using wood glue and a nail gun.

building a toy box out of wood
Repeat on the opposite end.

Then measure the front of the box at the bottom and at the top. Use those measurements to cut the front of the box. It should be close to 22", but depending on how square the box is the measurement may be slightly different.

building a toy box from wood
 Cut the piece and add it in place with wood glue and nails.

Now let's make the top. 

building the top of a diy toy box

Lay your 25" pieces of 1 X 4 side by side. 

building the lid to the toy box

 Place the 6" pieces of 1X2 on the 1X4's and nail them in place, using wood glue. This will be the inside of the lid.

wooden toy box with hinged lid
Attach the lid to the box with the hinges.

Then fill the nail holes with wood putty, if desired. I filled the holes on the box we painted, but not on this one.  If you wish to paint your toy box, I would recommend painting it before adding the hinges. I painted one box and we left the other natural wood. A coat of lacquer would protect the wood, but I haven't done that yet.

wooden toy chest

We've decided to put doll clothes in this one. I recently went through the baby clothes and gave them some newborn dresses to add to their collection of doll clothes. So now the toy box is nearly full.

wooden toy box used for toy storage

MORE DIY WOOD PROJECTS


2 comments :

  1. Wrong measurements for the side pieces it should be 10 3/4

    ReplyDelete
    Replies
    1. I definitely recommend measuring and cutting the pieces as you go - it's easier to get an exact fit that way. I just measured my toy box to double check and the side pieces are 10 inches, but if the width of your wood is different than mine, that could explain the difference needed.

      Delete